100/1000M Media Converters 20km
Product Brief Introduction
10/100/1000M Ethernet media converter adopts switching technology to fulfill media conversion. It complies with IEEE802.3z and IEEE802.3ab standards, and supports two types of media network connections: 10/100/1000Base-T and 1000Base-SX/LX. It inter-converts electrical signals of 10/100/1000Base-T twisted pairs with optical signals of 1000Base-SX, extending the transmission distance of a network from 100m via copper cables to 220m (fiber size: 62.5/125μm)/550m (fiber size:50/125μm) via fiber optical cables. It supports transmission in multi-mode dual fiber; single-mode dual fiber, single-mode single fiber.
switching technology to fulfill media conversion. It complies with IEEE802.3z and IEEE802.3ab standards, and supports two types of media network connections: 10/100/1000Base-T and 1000Base-SX/LX. It inter-converts electrical signals of 10/100/1000Base-T twisted pairs with optical signals of 1000Base-SX, extending the transmission distance of a network from 100m via copper cables to 220m (fiber size: 62.5/125μm)/550m (fiber size:50/125μm) via fiber optical cables. It supports transmission in multi-mode dual fiber; single-mode dual fiber, single-mode single fiber.
Media Converter Main Feature:
1.Supporting inter-conversion between 10/100/1000Base-TXand 1000Base-SX
2.Supporting full-duplex and half-duplex and its auto-sensed
3.Supporting automatic cross connection of twisted pair interfaces, facilitating system commissioning and installation
4.Supporting the transmission of extra-long VLAN packets
5.Supporting Quality ofService (QoS) and ensuring the transmission of VoIP packets
6.Supporting STP to form a redundant network
Technical
Parameter | Specification |
Access mode | 10/100/1000Mbps Gigabit Ethernet |
Standard | IEEE802.3ab 1000Base-T , IEEE802.3z 1000Base-SX/LX Gigabit thernet,IEEE802.1qVLAN,IEEE802.1p QoS,IEEE802.1d Spanning Tree |
Wavelength | 850nm/1310nm/1550nm |
Transmission distance | Dual-fiber multi-mode: 220m (62.5/125μm)/550m (50/125μm) Dual-fiber single-mode: 25/40/60/80Km Single-fiber single-mode: 25/40Km Category-5 twisted pair: 100m |
Port | One RJ45 connector:connected to STP/UTP category-5 twisted pair One fiber port: Multi-mode SC (fiber size: 50,62.5/125µm) Single modeSC/FC(fiber size: 9/125µm) |
Conversion means | Media conversion |
Delay | <10us |
BER | <10-9 |
MTBF | 100,000 hours |
LED | PWR(power supply), FX LINK (optical link action), TP LINK1000 (twisted pair link1000M), TP LINK100 (twisted pair link100M), TP ACT (twisted pair packet forwarding) |
PowerSupply | AC110-220V to DC5V 2A |
Power consumption | 5W |
Operating temperature | -10~55ºC |
Operating humidity | 5%~90% |
Maintaining temperature | -40~70ºC |
Maintaining humidity | 5% ~ 90% non-condensing |
Dimensions | 26mm (H) * 70mm (W) * 94mm (D) (external power supply) |
30mm (H) * 110mm (W) * 140mm (D) (internalpower supply) |
Installation of Media Converter:
1. Interface
RJ-45 interface
The transmission media adopts CAT5 twisted-pair with typical length of 100 meter. It features the function of automatically identifying the through line and cross wire
Fiber interface
SC/ST fiber interface is of duplex mode type, including two interfaces, namely TX and RX. When the two sets of optical transceiver are interfaced or connected to switch with fiber interface, the fiber is in cross connection, namely "TX-RX", "RX-TX" (direct butting for single optical fiber).
2. Connection
The network device(work station, hub or switch) with RJ-45 interface is connected to RJ-45 jack of optical transceiver through twisted-pair. And the multi/single mode fiber is connected to SC/ST fiber interface of the optical transceiver. Thenswitchon. The corresponding LED is on for correct connection. (See the table below for the LED indicatorlamp)
Cautions for Media Converter:
1. This product is suitable for indoor application.
2. Put on the dust cover of fiber interface when not used.
3. It is forbidden to stare at the TX fiber-transferend with naked eyes.
4. Single optical fiber transceiver must be used in pair (See the attachment description in delivery).
Troubles Shooting:
1. Device is not matched. Please select the corresponding network device according to the transferrate of the product (10Mbps or 100Mbpsor 1000Mbps) when connected to other network devices (network card, hub, switch).
2. Line loss is excessive during the fiber wiring. Excessive loss in connector plug-in and fiber soldering welding, and excessive intermediate nodes may cause excessive loss rate or abnormal operation.
Hot Tags: 100/1000m media converters 20km, China, manufacturers, suppliers, factory, wholesale, customized, Fiber Jumper, Fiber Optic Adapter
